Видео

Is there a spacer plate under the shifter?

I have the same exact code. The control board is what the code is for. I keep reading different answers. But the shift actuator was never even on the list for that code.

Awesome! How did it run?

I did all that, and replaced the part and NOTHING, still not passing SENSING

My third comment, the post install pic is cool, most videos forget to show the finished product.

After 7 years have passed, how do you like the lift kit sir?

Great video. I appreciate the detailed info.

This video was fantastic. I couldn't figure out how to change the ignition switch. This showed me exactly how. It was still very difficult to get out. Mine was very stuck, but its removal wouldn't have been possible without this video. Thank you!

My washer is spinning, but not enough to wear clothes are still wet. Could it be the belt or clutch?

This is a semi annual event for me fly wheel wont tighten up, should i reloave assembly or just try spring.

We rent and this is the washer that was here. We have a maintenance guy that owns an appliance repair shop and the employee he sent can't figure it out either. I absolutely hate these things. Been washing my stuff at my mother in law's house for a week now...

It doesn’t pop up you don’t know what you’re talking about

This needs much more explanation otherwise people following it will overtighten and wear their steering boxes out very fast. Its best to eliminate play from all other areas before messing with the box (i.e. tie rods, u-joints etc). If you adjust and your steering doesn't return to 45 degrees before centre then it's too tight and you need to slacken the adjustment otherwise your box will wear out fast.

Loose all the u joints get a double D shaft

I pulled the inter Drum, and used Dawn on the seal. That's just me......

“Lets see if we can start this guy” Cuts out the part where he starts it

Where is the rest of the video!?! You got 1/3 of the way and then just ended with “ok I’m done”. What happened? I mean, seriously, the cutting it off part is obvious, I wanted to see how you put it back together, any issues you ran into etc.

is it possible to remove the rubber seal from the transmission? or do I need to buy a whole new transmission?

Is it me or are Jeeps famous for ignition switches going bad? Thanks for sharing this with us 😊

Chinook

Thanks next time don't do any pain killers your high

Amazon review lead me here...good luck with your build

My washer is stuck in flood mode I believe. Nothing I've tried seems to fix it.

What a load of b.s. these washers are. Just need a basic fill, wash, rinse & spin. Washers lasted 20 yrs just doing that. No one should have to be a diagnostic tech or mechanic to have an appliance last a good 10 yrs at least.

You should sell some of them

Sensing shifter not working due to lid lock ? Is that possible? Replaced lid lock sensor but lid lock did not activate went through diagnostic steps to it washed see if it shifts past wash it was stuck in sensing ?! Now it advanced to wash?!

Built a off road vw bajo with close lights n porche. Parts with my brother in 1983 with a crome stinger tail pipe badass background

Damn the whole reason I was here is I lost my key lol was so disappointed when I got to the part where you need the key :(

What are the yellow and white switches called ? I disconnected mine and a small copper piece fell out as well and now I can’t get my jeep to start after finishing installation

how i can know gearbox need to change? whirlpool WTL1300SL

Why would you skip the procedure of taking the window off the regulator

600 $??????? It cost me 75 $ spark plugs and 165 $ coils....NGK ..ALL

I changed shifting sensor and it changed nothing….what next? Is my washer junk?

You saved me $600. THANK YOU.

NO do you understand how lucky you are to find a SERVICE manual just taped inside the washer ? I can't imagine they did that often and when they did that it stayed inside the washer when you come across one years later. if I had a manual, I wouldn't need you to explain a thing !

why does mini says fuel filter is lifetime 😅😅😅😅

My washer is having this exact problem. After pressing start while done is selected and all are blinking, I clicked it counterclockwise as you did in the video. It was blinking sensing. I tried diagnostic mode again but turned it clockwise and different things lit up. I am confused on what my issue is now 🥴

Needs to stay away from washing machines. I have to laugh as to why this machine is still working, I mean really. It's insane to watch this.

Is this washing machine diagnostics or safe cracking procedures? 🤔

Hello i have the same pedal assy in my bug. What size are your master cylinders?

Can’t get this to pop out at all. Do I have to use a super skinny flat head screwdriver head?

Now play dead 😂

Thanks for sharing. I just wish there were no so many places around that like to rip off women when they take their cars into the shop to get fix. I am currently having that lighting bolt and now I am depress cause I do not have no one I trust to take it to.

You should place a towel around the circumference of the basket inside. I saw you dropped a screw or a washer. That will keep them from going down into the bottom of the basin and potentially getting ground up while you’re doing laundry.

I cannot thank you enough for these Whirlpool videos. I'm 58 year old woman and we're always broke. Our less than 8 yo washer started messing up. We paid a repair man who ran a dx and reset for $70. Now I can do for free until we can figure out to replace the part (most likely the shift sensor shown in another video) or find a way to replace if part is too expensive. You are truly a Godsend.

Great video

You guys got gipped. Could have went online and got a new one for less that $100

Where did you get the spoiler on your bug at I want one

Every light came on and weren’t flashing when I tried self diagnosing. What does that mean?

Did you ever finish the install? I bought these same regulators for my 1-piece in a '70 Baja rebuild. I've had to bed the regulator brackets to get it to fit, and something still isnt right. Struggling.